- #Use impulse rc driver fixer with kiss gui install#
- #Use impulse rc driver fixer with kiss gui drivers#
- #Use impulse rc driver fixer with kiss gui manual#
selectable rotation direction with a solder jumper normal PWM input (1000-2000us 25-500Hz) and oneshot125 PWM(125-250us -> for use with up to 1kHz) selectable with a solder jumper 10-bit PWM resolution (~950 usable steps)
hardware in and output PWM (zero signal jitter) 32kHz output PWM frequency (not audible) low RDSon fets -> 3,5mOhm on the 12A and 1,66mOhm typical on the 18A version adaptive deadtime (no through shots but also minimum possible body/freewheel diode use -> less losses)
#Use impulse rc driver fixer with kiss gui drivers#
fast gate drivers (high efficiency because of very low switching losses) regenerative/active braking (because of the complementary PWM the ESC brakes the motor activ if the throttle signal goes lower) Active freewheeling (no partload problems) (complementary PWM) In the US: GetFPV, BuddyRC and BuildRCDronesįeatures: (except for the max continuous current and the price, both versions are almost identical) In Europe: Viacopter (worldwide shipping, 25% tax off for non-EU customers) New mini power distribution board for the KISSes by Flyduino KISS ESC 18A v1.1 with bigger solder pads (overall size 12x24mm) available at Flyduino now
#Use impulse rc driver fixer with kiss gui manual#
The KISS ESC 12A 2-4S v1.0 Īnd the KISS ESC 18A 2-4S v1.0 ģD version of the KISS ESC 12A and KISS ESC 18A available at Flyduinoĭownlad: Official Manual for the KISS 12/18A ESCS There are two versions v1.0 at the same size (12x23mm) and v1.1 (12x24mm) Note: We now have another thread dedicated to the KISS 30A version: Here are pictures of one of the first ones in line, the AIKON SEFM 30A.I´m proud to present our new multicopter high preformance/low cost small size ESC the KISS ESC's ( Keep It Super Simple) Or if you need to configure or update, just do so with the Simplicity offered by connecting to your ESCs through the FlightController, using BLHeliSuite and a USB cable.ĮSCs will be available from several manufacturers in not too long.
#Use impulse rc driver fixer with kiss gui install#
If you have a regular setup, just install and go fly (calibrate if your throttle range does not match BLHeli_S default). Last and by no means least, is Simplicity. Autodetected when the ESC sees an input signal. A BB1 MCU will support 350k erpm, and the limit of the BB2 is not yet known, so the code is set to limit at 500k erpm.īLHeli_S supports regular 1-2ms input signal, as well as Oneshot125, Oneshot42 and Multishot. The resolution varies between hardware configurations (MCU clock speed and driver type), and is between a nominal 512 steps and 2048 steps.īLHeli_S supports very high motor Speeds. This makes the motor Silent.īLHeli_S has very Small throttle Steps.
Maybe even better.īLHeli_S generally does Startup better than base BLHeli.īLHeli_S has motor PWM that is Synchronous to the MCU master clock, as it is generated by hardware. Two MCUs support this for BLHeli_S, namely the BusyBee1 at 24MHz (EFM8BB10F8) and the BusyBee2 at 48MHz (EFM8BB21F16).īLHeli_S will have the same good Sync holding properties as base BLHeli. BLHeli_S is an improved version of the base BLHeli code.īLHeli_S delivers a throttle response that is Smooth as Silk, and the main factor contributing to this, is that it uses hardware to generate motor PWM.